Saturday, May 1, 2010

Blogger in Action: 7D triggers handheld 580EXII

.
The popup flash of the Canon 7D can trigger an external Canon flash in slave mode . This is a very handy feature although I've found that the external flash must really be able to “see” the popup flash. For example, I had high hopes of using a 580EXII mounted in a Stroboframe above the 7D as a bounced light triggered by the 7D popup flash. That configuration doesn't work – the 580EX sensor just can't see the 7D popup. As shown below, there is a workaround.




Yes, that is your blogger and uncle of the bride getting snapshots at the reception. As awkward and fearful as I looked, it worked! That is, it worked so long as I was close to the subject; that large hall was as dark as a cave in places and had a high ceiling as well. The little 7D popup often was just not powerful enough – even for direct fill. (The photo of me was made by my wife using a 20D with direct flash from a 580EX.)
.

Saturday, April 10, 2010

Just Pictures

.
Some recent pictures using the 7D ...










.

Saturday, March 20, 2010

RF-602 Wireless Flash Trigger

.

Although I learned wireless “Strobist”flash techniques using the Cactus PT-04, I recently switched to the Yongnuo RF-602. In addition to being more reliable, the RF-602 can be used as a wireless shutter release for my Canon 7D. When I twisted off yet another PC connector from a Cactus PT-04 receiver, I gave up and ordered the RF-602. Perhaps I was just looking for an excuse but, whatever the reason, I now use the RF-602 for wireless flash triggering.


Like the Cactus units, the RF-602 is a simple trigger; that is, the flash is told “Fire” but flash intensity must be set in advance by the photographer. The transmitter, shown above, mounts on the camera and sends the signal to the receiver. The transmitter does not have an On/Off switch but does have a large button that can be used to trigger the flash or camera by hand. The transmitter uses one 3V CR2 lithium battery. The battery was included in the kit. The RF-602 system uses 16 channels but out-of-the-box is set to “ALL” so the first thing I did was to set a channel. The little switches are covered by a piece of tape. I left the tape on the switches and used a pencil point to change them.


The RF-602 receiver, shown above, uses two AAA alkaline batteries that were included in the kit. The battery door is a bit difficult to open – probably a good thing. The little switch on the receiver must be set to match the switch on the transmitter. The receiver does have an On/Off switch. The receiver has a flash shoe on top and a screw mount on bottom.

The RF-602 kit included a shutter connecting cord for my Canon 7D and a flash connecting cord. The flash connecting cord has a 3.5mm plug and a 6.35mm adapter plug. The basic kit does not include a PC cord so I've ordered one. Normally, I'll be using the hot shoe connection.


So far, the RF-602 system has handled everything I've thrown at it: Nikon SB24 and SB28 flashes, Vivitar 285HV, Canon 380EX, 420EX, 580EX, Yongnuo 460-II. The system works from my Canon G3, G9 and 7D. It triggers my Canon 7D. It appears to be more robust than the Cactus PT-04 system.
.

.
.

Sunday, March 7, 2010

More 7D DOF

.



I'm still often surprised by the limited depth of field from the 7D and similar sized sensors.  Sometimes the limited DOF is just what is wanted but other times more is needed.  It is those "other" times that I'm likely to forget to go to a higher numbered f-stop.

The above shot was taken today at f8.  Giving myself at least a little bit of credit, I purposely selected f8 as likely to give both foreground and background blur in the scene.  The point of focus was the first group of birds on the pier at a distance of about fifty feet or so.  I used the single point focus and recomposed -- probably focusing a bit short of the first bird.  According to the DOF calculations, the near focus should be about 38 feet and the far focus about 73 feet.  I didn't take any measurements but these distances are probably representative of the scene.

In this web sized view, the DOF is not so apparent but, believe me, it shows on a full size display.
.
.

Sunday, February 21, 2010

CF Cards for the 7D

.
One of the claims to fame of the Canon 7D is its burst speed of 8 frames per second.  One frequently asked question is "Which memory card should I buy?.  Burst speed is often associated with the speed of the memory.  I rounded up a small assortment of SanDisk cards and did a very quick test.

Canon recommends a UDMA compatible card.  Of the four cards tested, only my old 2GB Ultra II was not a UDMA card.  For video, Canon recommends a read/write speed of at least 8 MB/sec.  The old Ultra II is listed at 15 MB/sec, the Extreme IV as 45 MB/sec and the "Extreme" (no suffix) is 60 MB/sec. 

Rob Galbraith has researched, tested and published data for the performance of many memory cards.  I wanted to see for myself.  My normal practice is to shoot in RAW+JPEG mode with the JPEG at the smallest size.  I set the 7D for ISO 400, manual exposure, manual focus, IS turned on.  Each memory card was freshly formatted in the 7D.  My subject was the XNote Timer that I'd used previous to estimate G9 shutter lag.

I simply pushed the shutter button and held it down until more than 30 shots had been fired.  Of course, I never shoot this way but I wanted to see what would happen.

All the cards performed the same for the first eight shots.  That is, no matter which one of the cards was used, the 7D cranked out eight shots in about 0.9 seconds.  Apparently, these eight RAW+JPEG fill up the internal (buffer) memory of the 7D.   After those first eight shots, shooting rate changes.

With the Ultra II, the 7D required 21.7 seconds to fire off 30 shots; that is, 0.9 seconds for the first eight shots then 20.8 seconds for an additional 22 shots. 

The 60MB/sec Extreme(s) and Extreme IV all performed the same as far as I could tell.  With any of those cards, the 7D required 7.7 seconds to get off 30 shots; that is, the first eight shots required 0.9 seconds and the next 22 shots required 6.8 seconds.  The timing was not uniform between shots.  Two shots would be roughly 0.15 seconds apart followed by roughly a half second delay and then another two shots 0.15 seconds apart, etc., etc.

In practice, I've had a few impatient delays with the Ultra II in the 7D but not with the Extreme IV.  I can't speak to any quality or ruggedness differences between the Extreme IV and the Extreme (no suffix).  I've never had a problem with a SanDisk card.  The Extreme (no suffix) are less expensive than the Extreme IV so, for now, that's my card.
.

Tuesday, February 16, 2010

HD Video and the DSLR

.
I fully expected the Canon G11 to have HD Video and still can hardly believe that it does not.  Whatever the marketing or technical reasons for Canon's not including HD Video in the G11, the 7D has it and I bought the 7D instead (that should show them!).  I had and still have great plans for learning HD Video with my 7D but, so far, have done very little of it.  At least part of my hesitation is the very large learning curve in front of me 

I've recently found a "book" that should help:  "Mastering HD Video with Your DSLR" by Helmut Kraus and Uwe Steinmueller.   This is a 40MB downloadable E-Book in pdf format; it costs $29.95 and seems well worth the price to me.  Even though I'm only part way through the book I'm enthusiatic enough to recommend it to others.

One surprise though:  No video in the E-Book!  I've never seen video in a pdf file but I'll bet it is coming -- if not already available.
.

Sunday, February 14, 2010

YN460-II with 7D

.
I'm still pleased with the simple and inexpensive YN460-II flash described previously. Sure, all it does is flash when told to do so and its flash power must be set manually; that is, no automatic flash exposure at all. But the YN460-II does these basic things well. Also noted previously, the YN460-II works with the Canon 7D camera even when the 7D popup flash is set for ETTL mode provided the YN460-II is set in its own "S2" mode. Again, "works" means only that the YN460-II fires with the appropriate timing -- its flash power is not set by the 7D flash controls.

After a few days of tinkering, I suddenly wondered "What if the YN460-II actually interfered with the 7D popup flash?" To test my loss of faith, I set up a simple scene with the faithful Woof-Woof and fired off several shots at varying conditions. First, the base case using only the 7D popup flash is shown below. The 7D was set for ISO 200 using manual exposure and 1/250 second at f5.6. The 7D was set to ETTL mode using the internal flash only and without flash compensation. Using the Canon 15-85mm lens at mid-zoom, I was perhaps nine feet away from Woof-Woof. The white balance was set for "flash" in Adobe Camera Raw.
.


I then tried the 7D with the YN460-II in several positions using bounce and direct flash at varying power levels. Not much to report here except that the 7D flash obviously does not know or care about the YN460-II. The 7D fires its preflash (which the YN460-II ignores), computes the "correct" flash exposure without regard to the YN460-II and then fires away -- joined this time by the YN460-II. In other words, the 7D flash does not instantaneously change its mind when the YN460-II fires.

To get the shot below, the YN460-II was placed a little behind Woof-Woof and aimed directly at him. The YN460-II was set to 1/32 power; the 7D internal flash was in ETTL mode and set at -3 flash compensation. White balance was set in ACR at the "flash" setting.




Throwing a simple second flash into the mix certainly can add a new dimension to a shot!
.